Can You Answer These Questions a Master Carpenter Should Know?

By: Torrance Grey
Estimated Completion Time
4 min
Can You Answer These Questions a Master Carpenter Should Know?
Image: gilaxia/E+/Getty Images

About This Quiz

Carpentry is one of humanity's oldest lines of work, dating back to the times when homo sapiens stopped sleeping in caves or out in the open, and looked at trees as a a potential building material. Of course, humans didn't have power saws in those days, or even effective methods of metalworking that would make hand saws. So the first wooden homes were probably built from fallen logs and from branches that could be broken off trees. In a sense, we recall these early days when we call houses built from scratch "stick-built." (This means as opposed to prefab homes, where the building arrives on the job site in sections, which then need to be assembled).

Carpentry has grown in leaps and bounds since then (though it's still one of the more male-dominated professions in the modern world). Carpenters are well-educated these days, with a system involving apprenticeships, then journeyman status, then the level of master. How familiar are you with the things that master carpenters need to know? We've crafted a quiz to help you find out. Our quiz might seem easy at first, but don't be lulled into a false sense of confidence - it gets harder. Are you ready? No tools required; just your wits!

If a wall is "load-bearing," what does it do?
Supports the roof
Supports electrical wires
Allows you to hang art on it
All of these
Correct Answer
Wrong Answer

As you'd probably expect, a load-bearing wall holds up the roof. A wall doesn't need to be load-bearing to support art or a flat-screen TV.

Advertisement

A roof's steepness is called its what?
Angle
Density
Pitch
Yaw
Correct Answer
Wrong Answer

Though "angle" also sounds right, the correct term for this is "pitch." Among other things, a roof's pitch allows it to shed snow that might otherwise accumulate and put strain on it.

Advertisement

True or false: Carpenters make buildings, and only buildings.
True
False
Correct Answer
Wrong Answer

Carpenters also make furniture, as well as boats. Someone who makes a boat from wood in a traditional way is called a "shipwright."

Advertisement

Putting up the basic "skeleton" of a house is called which of these?
Barn-raising
Framing
Lifting
Establishing
Correct Answer
Wrong Answer

The basic wood skeleton of a house is its "frame." Framing was a big part of old-fashioned "barn raising," but that's actually a New England term for a community effort, putting up most of a new barn in a single day.

Advertisement

The vertical timbers (planks) of the frame are called what?
Abes
Lays
Joists
Studs
Correct Answer
Wrong Answer

You're probably familiar with the term even you've done even a small amount of home decorating. Finding the studs in walls allows you to hang heavier pieces of art or a rack to keep your bike indoors.

Advertisement

If you cut wood against the grain, it is called which of these?
Cross-cutting
Marking
Shearing
Very difficult
Correct Answer
Wrong Answer

What exactly is "grain?" Funny you should ask ...

Advertisement

What exactly is "grain"?
The darker knots in wood
The denseness of the wood's molecules
The way the wood cells grew when the tree was alive
Corn, barley, rye and such
Correct Answer
Wrong Answer

Wood, like meat, has "grain," a result of the natural way the tree (or animal muscle) grew. Butchers, like carpenters, either cut with or against the grain.

Advertisement

What is cutting parallel to the grain called?
Marking
Obfuscating
Ripping
There is no other term for it
Correct Answer
Wrong Answer

Sounds violent, but this is the common term for cutting with the grain. Experienced carpenters know when to cross-cut and when to rip.

Advertisement

Where would you find crown molding ?
In a bathroom
Between the wall and the ceiling
Above a door frame
In a wooden door
Correct Answer
Wrong Answer

Crown molding is ornamental woodwork between the top of a wall and the ceiling. Why can't the wall and ceiling just, you know, meet? We're not sure!

Advertisement

Which of these tools comes in "flat" or "Phillips" types?
Band saws
Miter saws
Plumb bobs
Screwdrivers
Correct Answer
Wrong Answer

This isn't just something that carpenters would know. The difference between a flat and a Phillips screwdriver is one of the first things people learn when they're learning about home repair.

Advertisement

Okay, what *is* the difference between a flat and a Phillips screwdriver?
The material of the blade: One is much stronger than the other.
The shape of the tip: one is straight-across, while the other is cross-hatched.
The shape of the tip: One is straight-across and the other is hexagonal.
One has a small motor and the other doesn't.
Correct Answer
Wrong Answer

A Phillips screwdriver is meant to fit into a plus-sign-shaped notch on the screwhead. If the notch is narrow and straight across, you need a flat screwdriver.

Advertisement

If lumber is "green," what is it?
Eco-friendly
Expensive
Newly cut
Of a rare type
Correct Answer
Wrong Answer

Green lumber usually needs to be air-dried or kiln-dried before use. Working immediately with green lumber is unwise.

Advertisement

Which of these tools does a carpenter not really need?
A band saw
A drill
A Geiger counter
A spirit level
Correct Answer
Wrong Answer

A Geiger counter detects levels of dangerous radiation, named for Hans Geiger. If you're a carpenter and you need this tool, ask for a raise -- you're working under dangerous conditions!

Advertisement

What is the name for framing elements that run horizontally?
Branches
Joists
Chords
Hypotenuses
Correct Answer
Wrong Answer

You hear the word "joist" less often than stud. This is probably because it's rarer to mount things on joists than on studs.

Advertisement

What differentiates a screw from a bolt?
Screws are smaller.
Screws are larger.
Screws can be made of wood.
Screws need no nut.
Correct Answer
Wrong Answer

Bolts require nuts on the other side of the building material to be correctly fastened. Screws embed themselves directly in the material, and do not require a nut; in fact, they usually don't emerge from the other side of the wood.

Advertisement

How far apart are studs in most houses?
5 inches
One foot
16 inches
Two feet
Correct Answer
Wrong Answer

This reminds us of our favorite parody of ghost-hunting shows and the tech they use. In it, a ghost hunter turns a stud seeker into a "spectre detector" and is shocked to find there's a spirit "every 16 inches!" His partner sighs sadly and says, "There usually are."

Advertisement

An interior door usually has how many hinges?
Two
Three
Four
Correct Answer
Wrong Answer

Doors between rooms tend to be lighter than ones between the building and the outdoors. That's why interior doors need only two hinges, usually, while exterior doors commonly have three.

Advertisement

In carpentry terms, what is a "plane"?
Any horizontal surface
Any surface that's been sanded smooth
A gauge for determining smoothness
A gauge for determining pitch
Correct Answer
Wrong Answer

"Plane" is a broad term in carpentry, and related to the same term in geometry. Instruments used for determining whether a plane is level are called, not surprisingly, "levels."

Advertisement

What is the term for work on the parts of the building visible to its owner and residents?
Interior carpentry
Finish carpentry
Trim carpentry
Either "finish" or "trim"
Correct Answer
Wrong Answer

It's not interior carpentry, because it's also done on the outside of the house. Essentially, this kind of work is the opposite of "framing," which is vital but hides under the plaster and drywall.

Advertisement

What is the handrail of a staircase called?
The baluster
The banister
The landing
The riser
Correct Answer
Wrong Answer

The other terms are also the names of staircase parts. But "banister" is probably the best-known one, because of the joy kids take in "sliding down the banister."

Advertisement

What is "beveling"?
Creating an angle on the edge of a piece of wood
Putting stone or cement under a sill plate
Restoring serration to a dull saw
Staining wood with natural materials
Correct Answer
Wrong Answer

Beveling can be ornamental; you'll see it in crown molding, for example. It can also soften the edge of wood that people might come into contact with often -- like the edge of a dining table.

Advertisement

Where would you find a "gable"?
A basement
A door frame
A roof
Old Hollywood
Correct Answer
Wrong Answer

A gable is a triangular section of roof. You'll see smaller gables jutting out from the roof of a house with an attic -- they provide extra head space. This is especially useful when the attic is used as living space, like a bedroom.

Advertisement

A level which uses a bubble in fluid, inside a clear tube, is called what?
An air level
A hydro-level
A spirit level
A Wright level
Correct Answer
Wrong Answer

The "spirit" is the fluid inside. When the bubble of trapped air is completely in the center of the tube, the surface the level is resting on isn't slanted.

Advertisement

Which of these carpenter's tools has "bore"?
Drill
Hammer
Plumb bob
C-clamp
Correct Answer
Wrong Answer

The term "bore" refers to the diameter of the drill bit, and the size of the hole it makes. You hear the same term in the engineering of tunnels.

Advertisement

"Riser" and "tread" are terms used in relation to what part of a house?
The floor
The doors
The staircase
The walls
Correct Answer
Wrong Answer

The riser is the vertical part of the step. The tread is the horizontal part, on which the foot lands. The "going" refers to the distance in feet the staircase covers from the first step to the top landing. (It helps to visualize this as a line drawn along the bottom of the staircase.)

Advertisement

Which of these carpentry terms recalls a priest's clothing?
Dovetail joint
Eave
Miter joint
Prefabrication
Correct Answer
Wrong Answer

A miter joint connects two angled pieces of wood. In an ecclesiastical setting, a miter is a bishop's hat.

Advertisement

Which of these names is a type of roof?
Eldritch
Gambrel
Ichor
Antiquarian
Correct Answer
Wrong Answer

Gambrel roofs are common to New England, and appear with clockwork regularity in the work of Rhode-Island-born horror writer H.P. Lovecraft. (Bonus points if you recognized the other words as three of Lovecraft's favorites as well!)

Advertisement

True or false: "Hardwood" does not actually refer to the density or hardness of the wood itself.
True
False
Correct Answer
Wrong Answer

Generally speaking, a "softwood" comes from a conifer tree, like a pine. Hardwoods come from deciduous trees like oak. Within those categories, there is a varying degree of actual hardness.

Advertisement

The part of the drill that holds the bit is called what?
The chuck
The collar
The join
The mouth
Correct Answer
Wrong Answer

We're not sure why this needed a specialized term, but there it is. Don't mark yourself as a novice by saying you inserted the drill bit "into the drill." Amateur!

Advertisement

What is the lowest framing element of a building called?
Ground plate
Sill plate
Sole plate
Any of these
Correct Answer
Wrong Answer

This important part of the frame has several names. "Midnight sill" is another that you might hear.

Advertisement

What is an "architrave?"
An exam in architecture school
Decorative woodwork around a door frame.
Extra support for the sill plate
The arms that hold up rain gutters
Correct Answer
Wrong Answer

Architraves are molding that hides where the door frame meets the wall. Seriously, what's with builders not wanting people to see where surfaces join?

Advertisement

Which of these food-related terms is used in carpentry?
Biscuit
Huckleberry
Onion
Slice of pie
Correct Answer
Wrong Answer

A "biscuit" is an oval disk of wood. It has several purposes in woodwork. Putting gravy on this sort of biscuit is not recommended, and you'd be wasting jam on it, as well.

Advertisement

What is a nail set used for?
Keeping different weights of nails apart
Keeping nails from bending during hammering
Sinking a nailhead a bit lower than the wood's surface
Manicures
Correct Answer
Wrong Answer

When nailheads are lower than the surface of the wood, things look nicer. But it's a pain if you're a homeowner trying to remove a nail with a simple claw hammer.

Advertisement

"Flush," "proud" and "shy" all refer to what?
The grit of sandpaper
How pieces of wood fit together
The decorations on a roofline
They are slang terms for master, journeyman and apprentice
Correct Answer
Wrong Answer

You've probably heard the term "flush" for pieces of any material that fit perfectly together. Rarer are "proud" and "shy"; they are terms for the piece that sticks up and the piece that's lower down, respectively.

Advertisement

What nation is IKEA headquartered in?
Canada
Italy
Poland
Sweden
Correct Answer
Wrong Answer

IKEA is actually the enemy of carpenters everywhere, what with their meticulously assembled furniture kits. However, thanks to the complexity of the directions to assemble said kits, a lot of carpenters have lucrative side gigs assembling IKEA furniture!

Advertisement

You Got:
/35
gilaxia/E+/Getty Images