Quiz: Do you know the dirt on how to repair a washing machine?

Staff

4 Min Quiz

Image: refer to hsw

About This Quiz

In today's busy households, it's extremely inconvenient if the washing machine breaks. Before you panic at the first sign of trouble and call a technician, take our quiz to see if you can diagnose and fix the problem yourself.

What is the typical life span of a washing machine?

According to the National Association of Home Builders, a washing machine will typically last a decade. Of course, they can last a lot longer with proper care and maintenance.

Advertisement

What should you always do before working on your washing machine?

Be sure to disconnect the water hoses and the grounding wire before you do any work on your washing machine.

Advertisement

What is the first thing you should do to diagnose a washing machine problem?

First and foremost, check the power supply to the washing machine. Test the plug, cord and outlet and then check for blown fuses in the electrical panel.

Advertisement

How do you check to the water temperature settings for your washing machine?

Follow the manufacturer's instructions to check the switches on the control panel. If washing with heated water, make sure the temperature is set to at least 120 degrees Fahrenheit (49 degrees Celsius).

Advertisement

Which liquid can be used to clean a washing machine that has smelly soap buildup?

Run the machine through a full cycle with just water and 1 gallon (3.8 liters) of vinegar. If the tub still smells, wipe the inside with a bleach and water solution. If you use bleach though, wash a load of whites after cleaning so that any remaining bleach will not ruin colored clothes.

Advertisement

Which of the following is usually the cause of the washer overflowing with water?

The small hose connected to the water level control switch can loosen and fall off the connection, usually causing the water in the tub to overflow. To fix it, cut about 0.5 inches (1.3 centimeters) off the end of the hose, and use a push fit to reconnect it to the switch. Push fit connections can be found at any hardware or home improvement store.

Advertisement

What is likely to clog a lid switch and prevent it from opening?

A buildup of detergent can sometimes clog the lid switch, and if this part becomes obstructed, your washing machine will not work.

Advertisement

How can you tell if the lid switch is faulty?

To see if your lid switch is faulty, test it with a volt/ohm meter (VOM). If the meter reading is zero, your switch is working fine.

Advertisement

What regulates the water temperature in your washing machine?

The temperature selector switch regulates the temperature of the water in the tub and also helps control the fill cycle.

Advertisement

A defective water level control switch can cause what messy problem?

If the water level control switch malfunctions, you can have a flood on your hands.

Advertisement

How many washing machine operations does the timer control?

The washer timer, whether digital or mechanical, is responsible for most washer operations, including cycle time, water level, and tub filling and emptying.

Advertisement

If your washer fills slowly or not at all, which part could be faulty?

If your washer overfills, fills slowly or doesn't fill at all, the water inlet valve could be the problem. Luckily, it's simple and inexpensive to replace.

Advertisement

What typically reliable part of your washing machine is likely to make a lot of noise when there is a problem?

Though it rarely needs replacing, the tub or basket can make noise, vibrate or stop completely if the washing load becomes unbalanced. If that happens, just redistribute the clothes in the machine, and it should go back to normal.

Advertisement

What's the first step in replacing your washing machine's agitator?

It's very easy to replace the agitator on a top-loading washer. Simply unscrew the agitator cap, remove the old agitator, replace it with a new one of the same type and screw the cap back on.

Advertisement

What can cause your washing machine to vibrate a lot?

The snubber is a padded device located under the agitator cap. If the pad is worn out or its spring is broken, it can cause the machine to vibrate .

Advertisement

What can cause your washer's tub to suddenly stop?

Sudden tub stops can be due to a faulty motor belt, but most are caused by overloading the tub. Remove a few pieces of laundry, and you should be good to go.

Advertisement

Which of the following is a sign that your washer's water pump is broken?

The pump in your washing machine is one of its most hardworking parts. When the pump breaks, you can hear a clanging noise inside the machine, and the water doesn't drain out of the tub.

Advertisement

What happens when the drive belt of your washer wears out?

When the drive belt of a washing machine becomes worn or damaged, the machine makes noise, and the washer may stop altogether. A damaged drive belt is easy to replace.

Advertisement

How are pulleys attached to shafts in your washer?

The pulleys are attached to shafts with setscrews. Check that these screws are tight so the pulley or belt won't slip out of place.

Advertisement

Why are washing machines particularly difficult to fix?

Unlike simpler appliances, washing machines have many settings and complicated cycles that are controlled by timers. With so many components, it's often difficult to narrow down exactly what the problem is and how to fix it.

Advertisement

About HowStuffWorks Play

How much do you know about dinosaurs? What is an octane rating? And how do you use a proper noun? Lucky for you, HowStuffWorks Play is here to help. Our award-winning website offers reliable, easy-to-understand explanations about how the world works. From fun quizzes that bring joy to your day, to compelling photography and fascinating lists, HowStuffWorks Play offers something for everyone. Sometimes we explain how stuff works, other times, we ask you, but we’re always exploring in the name of fun! Because learning is fun, so stick with us!

Explore More Quizzes